Lagler Hummel belt sander on 3.25-inch red oak hardwood floor sanded bare in Raleigh NC

Raleigh, NC · Wake County

Hardwood Floor Sanding, Raleigh NC

For hardwood floor sanding, Raleigh NC homeowners pay $5.50 to $8.00 per square foot as part of a full refinish ($1,500 minimum): sanded to bare wood, sealed, and finished with two coats. If your finish is only dull, a recoat with no sanding costs less, and we will tell you which one your floor needs.

5.0 Google Rating58 Verified ReviewsBona Certified CraftsmanLow-Dust Containment24 Years in Business

Sand or Recoat

Does Your Raleigh Floor Need Sanding to Bare Wood?

It needs sanding if the finish is worn through to the wood, if you want a new color, or if the damage is in the wood rather than in the finish. If the finish is intact and only dull, it needs a recoat instead.

A recoat cleans and lightly abrades the existing finish, then adds one fresh coat of Bona Traffic HD. It costs $2.25 to $3.00 per square foot with a $750 minimum and is usually done in a day. See our hardwood floor recoating in Raleigh page if the list on the right points that way, or read how screen-and-recoat works in general. The wood flooring industry's consumer site describes the same split between a maintenance coat and a full sand and refinish.

One catch: floors that have had polish or wax products on them need testing first, because new finish will not bond over that buildup. Some of those floors need sanding even when the wear looks light.

What you seeUsual call
  • Finish worn through to gray or bare wood in traffic lanesSand
  • You want a different stain color, or no color at allSand
  • Deep scratches, pet stains, or water marks in the wood itselfSand
  • Amber, yellowed oil-based poly from the 1980s or 1990sSand
  • Cupped or crowned boards, after the moisture source is fixedSand
  • Finish dull but intact, color still rightRecoat
  • Light surface scuffs that stop in the finishRecoat
  • Floor refinished in the last several years and kept upRecoat

What Hardwood Floor Sanding Raleigh NC Projects Cost

Sanding is priced as part of a full refinish, because a sanded floor has no finish left on it. The full process, from first cut to final coat, is on our hardwood floor refinishing in Raleigh page.

$5.50 to $8.00

per sq ft

Sand and refinish

Sanded to bare wood, sealer, and two finish coats. Hardwax oil is one coat. $1,500 project minimum.

$2.25 to $3.00

per sq ft

Recoat, no sanding

One coat of Bona Traffic HD over the existing finish. $750 minimum.

$0

preliminary estimate

From your photos

Send photos and measurements and we reply the same business day. Some projects need an in-home assessment: a $100 fee, confirmed before the visit, which may be credited toward your deposit.

Where a Raleigh floor lands in the range depends on species, condition, how many grits it takes to get flat, and whether it gets stain. Exact pricing comes in your written proposal.

Addition and family room 3.25-inch white oak sanded bare before stain application in Hayes Barton Raleigh NC

Hayes Barton, Raleigh: 3.25-inch white oak sanded bare and flat, new lace-in boards and the original floor reading as one surface before stain. See the full project.

Raleigh Floors

Sanding Raleigh's Older Oak Floors

Original oak in Oakwood, Mordecai, Cameron Park, Five Points, and Hayes Barton can usually be sanded again, but only as much as the remaining wood allows, so we check before we cut.

Many of these homes sit on crawl spaces, and their floors are 80 to 120 years old. Some have been sanded several times already. Some are narrow strip flooring that was face-nailed, with nail heads close to the surface. On these floors we set every exposed nail, start as fine as the old finish allows, and run the Bona PowerDrive, which removes less wood per pass than a drum sander.

Newer Raleigh floors bring different questions. Midtown and north Raleigh homes from the 1980s and 1990s often have red oak under amber oil-based poly, which takes a full sanding to remove. Brier Creek, Wakefield Plantation, and North Hills have more engineered hardwood over slab, where the wear layer thickness decides how far we can go.

Homes built before 1978: if any of the surfaces being worked on, such as painted shoe molding, baseboards, or a painted floor, could carry old lead paint, the EPA's guide for homeowners planning renovation work explains what to ask about and how to protect your family. Raise it when you send photos so we can talk through the scope.

Passes and Grits

How Many Sanding Passes a Raleigh Floor Takes

Most floors take three or four grits across the field, plus edge and perimeter passes at matching grits. Each grit removes the scratch left by the one before it.

Our main field machine is the Bona PowerDrive, a planetary sander with heads turning in opposite directions. Bona explains the benefits of the Power Drive for flatness and scratch pattern. On floors that need real leveling we open with the Lagler Hummel drum sander, then finish with the PowerDrive. The full equipment list is on our main hardwood floor sanding page.

  1. 36 to 60 grit

    The first cut

    Takes off the old finish and flattens the floor. On a thin historic floor we start as fine as the old finish allows, to save wood. Heavy damage or a floor that has to come flat starts coarser.

  2. 80 grit

    Clear the first scratch

    Edges are cut at 80 grit before the 80 grit field pass so the wall line and the field carry the same scratch. Every scratch from the first cut has to be gone before this grit ends.

  3. 100 to 120 grit

    Ready for color or finish

    The final field pass, then a random orbital at 100 around the perimeter. White oak often gets a 120 final. Going much finer polishes the wood closed and stain takes unevenly.

Close-up of 3.25-inch white oak boards sanded bare showing clean grain detail before finish in Raleigh NC

White oak after the final grit: flat, clean grain, ready to take stain evenly.

What Raleigh Homeowners Need to Know

Technical Considerations for Hardwood Floor Sanding in Raleigh, NC

How long does floor sanding take in Raleigh?

Sanding usually takes two days on an average home, and the whole refinish runs four to six working days. Day one is setup, containment, and the coarse cuts. Day two is the finer grits, edges, and a vacuum and tack so the floor is clean for color. Stain, sealer, and two finish coats follow. Bona Traffic HD reaches full cure in 3 days; Bona Mega ONE and hardwax oils in 5 days. Larger homes, or older floors that take extra grits to come flat, can add a day.

Is dustless sanding truly dust-free?

No, it is low-dust. Every sander runs into a cyclonic dust separator and a HEPA vacuum, doorways are sealed with plastic, and air scrubbers run on your air returns. That keeps sanding dust out of most of the house, but fine dust still settles near the work area.

How much wood does a sanding remove, and is there enough left?

A careful sanding removes as little wood as the job allows, and a true 3/4 inch solid floor can be refinished 6 to 10 times that way. A floor that has to be sanded flat after cupping or heavy damage spends more. Our guide to how many times hardwood floors can be refinished walks through the math.

Engineered floors depend on the wear layer, the real wood above the plywood core. A 6 mm layer behaves like solid. A 3 to 4 mm layer can take three to seven refinishes. 2 mm is the thinnest we will sand, with one light sanding planned. North Raleigh homes with prefinished floors from the 1990s and 2000s are often ready for their first sanding; see can prefinished hardwood be refinished.

Stain color and water-popped stain preparation after the final grit

Every floor that gets color gets water-popped stain preparation after the last grit. Misting the bare wood opens the grain so stain goes on deeper and more evenly, which matters on the red oak common in Five Points and Cameron Park, where grain varies board to board. We put stain samples down on your own sanded floor so you see the color in your own light. Our article on water popping hardwood floors shows what it changes.

When sanding is not the right answer

Sanding is the wrong first step when the floor is too thin to cut again, when the tongue is showing at board edges, or when the boards are still cupped from moisture. Sand a cupped floor flat before it dries and the board edges shrink back, leaving crowned boards. On Raleigh crawl-space homes the fix starts below the floor, so read why hardwood floors cup in NC first, and if boards need replacing, our hardwood floor repair in Raleigh work comes before the sanding.

Raleigh Floor Sanding Questions

Sanding is priced as part of a full refinish: $5.50 to $8.00 per square foot with a $1,500 project minimum. That covers sanding to bare wood, a sealer coat, and two finish coats (hardwax oil is one coat). If your floor only needs a fresh topcoat, a recoat with no sanding runs $2.25 to $3.00 per square foot with a $750 minimum. Send photos and rough measurements for a free preliminary estimate and we reply the same business day.

If the finish is worn through to gray or bare wood, or you want a different color, the floor needs sanding. If the finish is intact and only dull or lightly scratched, and you like the current color, a recoat is usually enough. Floors that have had polish or wax products on them need testing first, because a recoat will not bond over that buildup. We tell you which one your floor needs from your photos, or at an in-home assessment when photos cannot answer it.

A true 3/4 inch solid floor, or an engineered floor with a 6 mm wear layer, can be refinished 6 to 10 times when each sanding removes as little wood as the job allows. A 3 to 4 mm engineered wear layer can take three to seven. A 2 mm wear layer, the thinnest we will sand, can take one to three. On older Raleigh floors that have already been sanded several times, we check what is left at a vent or threshold before we recommend anything.

Sanding itself usually takes two days on an average home. The full refinish, with stain, sealer, and two finish coats, usually runs four to six working days. A recoat with no sanding is typically done in one day.

No. It is low-dust, not dust-free. Every sander runs into a dust separator and HEPA vacuum, we hang plastic at doorways, and air scrubbers run on your air returns. That keeps most of the dust out of the rest of the house, but some fine dust still settles near the work area. Plan to cover electronics and anything you care about in adjoining rooms.

Usually yes, after we check how much wood is left. Many of these floors are 80 to 120 years old and have been sanded before, and some are thin strip flooring that was face-nailed. We set any exposed nails, start as fine as the old finish allows, and run the Bona PowerDrive, which removes less wood per pass than a drum sander. If a floor is too thin for another sanding, we tell you before any work starts.

Often, yes, if the wear layer is at least 2 mm. The thickness of that top layer of real wood decides it. Floors with deep bevels or a hand-scraped texture spend most of a thin wear layer just getting flat, so they need a closer look. We look at a board edge at a vent or threshold before we recommend a full sanding.

No. Most Raleigh homeowners stay home. The rooms being sanded are off limits while we work, and you stay off the floor while stain and finish are drying. The rest of the house stays open.

Send Photos, Get an Answer the Same Business Day

A few photos of the worn areas and rough room sizes are enough for a free preliminary estimate and a sand-or-recoat call. Text 984-400-7181 or call 984-400-4OAK (4625). Our showroom is in Clayton, and Raleigh is part of our regular service area; see all of our flooring services in Raleigh, NC.

Where We Work

Serving the Triangle Since 2002

Based in Clayton, NC. We travel throughout Johnston, Wake, and Durham Counties. Call to confirm your specific location.

Johnston County

Home Base
  • Clayton
  • Garner
  • Smithfield
  • Selma
  • Four Oaks
  • Benson
  • Kenly
  • Princeton

Wake County

  • Raleigh
  • Garner
  • Cary
  • Apex
  • Fuquay-Varina
  • Holly Springs
  • Wake Forest
  • Knightdale
  • Wendell
  • Zebulon

Durham and Orange Counties

  • Durham
  • Chapel Hill
  • Hillsborough

Don't see your city? Call us. We consider jobs outside these areas on a case-by-case basis, particularly for larger projects.

984-400-4OAK (4625)

Ready to Get Started?

Start With a
Free Estimate

Serving Clayton, Garner, Raleigh, Cary, and communities throughout Johnston, Wake, and Durham Counties. We respond the same business day.

Want us to come out? Request an in-home assessment →

Bona Certified CraftsmanFive-Year Workmanship Warranty24 Years in BusinessFully InsuredShowroom in Clayton, NC

After you request an estimate, we review your photos and project details and send a free preliminary estimate. When a project needs an in-home assessment, we confirm any assessment fee before scheduling the visit. You will receive a written proposal with the scope, products, timeline, and warranty clearly explained.

Want to see our work first? Browse the portfolio →

Text UsRequest a Free Estimate